International Scientific Journals
of Scientific Technical Union of Mechanical Engineering "Industry 4.0"

  • Journals
  • Submission
  • Events
  • About us
  • Contact

Author: Sitnik L. J.

  • EKOMPAKT, A NEW TECHNOLOGY FOR OBTAINING ENERGY FROM BIOMASS

    • Sitnik L. J.
    • Janicka A.
    • Walkowiak W.
    • Wrobel R.
    • Andrych M.
    Machines. Technologies. Materials., Vol. 9 (2015), Issue 9, pg(s) 17-19
    • Abstract
    • View Article
    •  Article PDF

    In the Division of Vehicle Engineering ,Wroclaw University of Technology, there is realized the grant which aim is to work out the innovative compact EKOMPACT module- the installation of electric energy generation from biomass renewable resources by new technology. Research results (primarily simulation) provide necessary data for any modification of the installation in a way that the implementation of a new solution will be possible in diverse locations which are characterized by different working conditions.

  • COMBUSTION ENGINE INTAKE PORT DESIGN ANALYSIS

    • Gandyk M.
    • Tkaczyk M.
    • Sitnik L. J.
    • Uzuntonev T.
    Machines. Technologies. Materials., Vol. 9 (2015), Issue 8, pg(s) 29-31
    • Abstract
    • View Article
    •  Article PDF

    Engine “breath” air through the intake ports. It is important part of every engine which has influence to the final characteristic. In this article is shown from where the design of intake port result. Article shows books theory with compare to 1D CFD analysis.

  • TESTING THE EFFICIENCY OF INTERNAL COMBUSTION CATALYSTS PO-SITION MODEL.

    • Andrych-Zalewska M.
    • Sitnik L. J.
    • Walkowiak W.
    • Aleksieva V.
    Machines. Technologies. Materials., Vol. 9 (2015), Issue 8, pg(s) 26-28
    • Abstract
    • View Article
    •  Article PDF

    In order to determine the effectiveness of the catalytic coating applied to the engine valve, a study model. For this purpose built test stand made of elements of the real engine. The catalyst temperature was controlled by electric heating. The position of the working gas fumes were collected with a spark-ignition engine, idling. Performed a simultaneous measurement of gas composition at the inlet to the model and the output from the system. The study was conducted at a constant flow rate and variable temperature exhaust gas catalyst sys- tem. The results of the study are presented in the form of comparative charts. It has been found highly effective activity of the catalyst for carbon monoxide and relatively high efficiency for hydrocarbons. Measurements of nitric oxide levels showed no significant changes in concentration in a range of temperatures.

  • THE HEAT BALANCE OF ENGINE FED BY DIESEL OIL AND BMD BIOFUEL

    • Andrych M.
    • Sitnik L. J.
    • Walkowiak W.
    Machines. Technologies. Materials., Vol. 8 (2014), Issue 4, pg(s) 38-40
    • Abstract
    • View Article
    •  Article PDF

    In the present paper the issue of external heat balance in the diesel engine is presented. The methodology of heat balance estima- tion, as well as the comparison of the researches results concerning engine with the common rail injection system, which is fed by mineral diesel oil and BMD biofuel has been presented. The impact of biofuel on the nature of changes in the heat balance has been estimated. The researches were performed on the measurement station based on the 13 points ESC test. It has been stated that the use of fuel assigned in the ESC test in the engine fed by biofuel (BDM) slightly increases in comparison to the engine fed by mineral diesel oil (ON). However, there can be noticed the change of the flow of energy input in the heat balance of the engine fed by both types of fuel.

  • INFLUENCE OF INTERNAL COMBUSION CATALYST TO SHORTEN THE INGNI-TION DELAY

    • Andrych M.
    • Sitnik L. J.
    • Walkowiak W.
    Machines. Technologies. Materials., Vol. 8 (2014), Issue 3, pg(s) 32-35
    • Abstract
    • View Article
    •  Article PDF

    The paper presents a discussion of the combustion processes in the engine piston, in terms of ignition delay. The problem of the physical and chemical ignition delay is discussed and equations which allow the calculation of ignition delay based on the theory of com- bustion processes are presented. The paper proposes the use of a catalytic coating in the combustion space in order to shorten the ignition delay. The results of studies made on single diesel engine are displayed. Studies have confirmed a significant effect of the catalyst on the combustion process and shortening the ignition delay. Internal combustion catalyst used as a coating made of ZrO2 activated Pt and Rh deposited on engine valves, caused a shortening of ignition delay of about 1 – 3 degrees of crankshaft rotation.

  • THEORY OF CUMULATIVE FUEL CONSUMPTION AND EXAMPLE FOR ITS APPLICATION

    • Sitnik L. J.
    Machines. Technologies. Materials., Vol. 8 (2014), Issue 3, pg(s) 17-20
    • Abstract
    • View Article
    •  Article PDF

    the theory of cumulative fuel consumption has been presented. The example of interurban bus research results have shown the way of getting to mathematical model of cumulative fuel consumption and the intensity of cumulative fuel consumption. The high value of pres- cience quotients is not a case- similar values were obtained in various different cases.

Congresses and conferences

  • IX International Scientific Conference
    "High Technologies. Business. Society"
    04.-07.03.2024 - Borovets, Bulgaria
  • XXI International Congress
    "Machinеs. Technolоgies. Materials."
    Winter session
    06.-09.03.2024 - Borovets, Bulgaria
  • XIX International Scientific Technical Conference
    "Foundry"
    17.-19.04.2024 - Pleven, Bulgaria
  • XXXI International Scientific Conference
    "trans&MOTAUTO"
    24.-27.06.2024 - Varna, Bulgaria
  • IX International Scientific Congress
    "Innovations"
    24.-27.06.2024 - Varna, Bulgaria
  • IX International Scientific Conference
    "Industry 4.0"
    Summer session
    26.-29.06.2024 - Varna, Bulgaria
  • XII International Scientific Congress
    "Agricultural Machinery"
    26.-29.06.2024 - Varna, Bulgaria
  • XI International Scientific Conference
    "Engineering. Technologies. Education. Safety"
    02.-05.09.2024 - Varna, Bulgaria
  • X International Scientific Conference
    "Materials Science. Non-Equilibrium Phase Transformations"
    02.-05.09.2024 - Varna, Bulgaria
  • XVII International Conference for Young Researchers
    "Technical Sciences. Industrial Management"
    04.-07.09.2024 - Varna, Bulgaria
  • XXI International Congress
    "Machines. Technologies. Materials"
    Summer session
    04.-07.09.2024 - Varna, Bulgaria
  • IX International Scientific Conference
    "Conserving Soils and Water"
    09.-12.12.2024 - Borovets, Bulgaria
  • VIII International Scientific Conference on Security
    "Confsec"
    09.-12.12.2024 - Borovets, Bulgaria
  • IX International Scientific Conference
    "Industry 4.0"
    Winter session
    11.-14.12.2024 - Borovets, Bulgaria
  • VI International Scientific Conference
    "Mathematical Modeling"
    11.-14.12.2024 - Borovets, Bulgaria

Scientific Technical Union of Mechanical Engineering "Industry-4.0"

108, Rakovski Str., 1000 Sofia, Bulgaria
tel. (+359 2) 987 72 90, tel./fax (+359 2) 986 22 40,
office@stumejournals.com