• Machine Learning Prediction of Mechanical Properties for Al-Cu Alloys Using Monte Carlo Data Augmentation

    pg(s) 111-113

    This study presents a machine learning framework for predicting the mechanical properties of 2xxx series Al-Cu alloys (2024, 2219, 2524) across 11 temper conditions. Monte Carlo augmentation generated 8,800 synthetic samples from compositional specification ranges of a literature-mined dataset. Three regression models, Random Forest, Gradient Boosting, and SVR-RBF were evaluated via 5-fold cross-validation (CV) to predict ultimate tensile strength (UTS), yield strength (YS), and elongation. All models achieved coefficient of determination R² > 0.991, with Mean Absolute Error MAE ≤ 7.4 MPa for UTS, ≤ 5.4 MPa for YS, and ≤ 0.51% for elongation. Feature importance analysis revealed that temper condition encoding dominated predictions (>75% importance), while individual compositional features contributed <5% each. The high predictive accuracy reflects the effectiveness of the augmentation scheme in capturing withingroup property–composition–temper relationships, though generalization to unseen alloy–temper conditions remains to be validated. The results illustrate the potential of combining corpus-mined data with Monte Carlo augmentation for rapid alloy property screening.

  • Cathodic Protection Modeling of Steels in Corrosive Chemical Environments Using COMSOL Multiphysics

    pg(s) 108-110

    This study investigates the electrochemical performance of Sacrificial Anode Cathodic Protection (SACP) systems for offshore steel structures using Finite Element Analysis (FEA). Two structural substrates, S235JR carbon steel and S550QL high-strength steel, were modelled in a 3 wt.% NaCl electrolyte. A comparative analysis was performed between two sacrificial anode materials: a conventional Al- 5Mg alloy and a quaternary Al-6Zn-0.2In-1Mg-0.03Ti alloy. The simulations evaluate the influence of anode placement errors by comparing an ideal symmetric distribution (90°) with a clustered configuration (10°). The results show that geometric clustering significantly alters the potential distribution along the structure. For S235JR steel, the clustered configuration produces localized underprotection with potentials reaching −0.78 V (vs. Ag/AgCl). In contrast, for S550QL steel, the same configuration results in localized over-polarization (≈ −0.96 V), thereby increasing the risk of hydrogen-induced stress cracking (HISC). The study demonstrates that improper anode placement may compromise cathodic protection efficiency even when high-performance anode alloys are used. These findings highlight the importance of accurate anode distribution and support the use of numerical simulations in digital twin approaches for offshore corrosion management.

  • Modeling of Densification Kinetics during Electro-Pulse Consolidation of Titanium Powder

    pg(s) 103-107

    This study presents a theoretical investigation of the densification kinetics of titanium powder during electro-pulse consolidation. A mathematical model was developed to analyze the influence of electrical current parameters in different sintering regimes – direct current (DC), alternating current (AC), pulsed current, and their superposition – on the thermophysical processes governing sintering.
    The heating rates and the evolution of relative density were calculated for different applied pressing pressures. The results show that the superposition of currents is the most energy-efficient regime. This regime enables the material to reach a relative density above 99% within a minimal processing time. The effect is attributed to the combined action of intense Joule heating and the electroplastic effect.

  • A methodological framework for achieving sustainable hydrogen supply chain produced via biogas-based steam methane reforming

    pg(s) 99-102

    Growing energy and environmental challenges highlight the need for a transition to sustainable supply chains. This paper presents a methodology for assessing a hydrogen supply chain based on steam reforming of biogas (SMR), as a low-carbon alternative to conventional natural gas. The framework covers the entire life cycle, from feedstock to end use. The proposed framework supports strategic planning and provides a basis for future modeling, optimization, and assessment of environmental and socio-economic benefits.

  • Implementation of slow stress rating test method (SSRT) in determination susceptability to hydrogen embritlement of P460NL1 steel

    pg(s) 94-99

    The hydrogen embrittlement susceptibility of P460NL1 pressure-vessel steel was assessed by slow strain rate testing (SSRT) with in situ electrochemical hydrogen charging. An electrochemical cell integrated with a tensile testing machine was used to generate hydrogen in a 3.5 wt.% NaCl solution containing 1 g/L thiourea. Cathodic charging was applied at a constant current of −20 mA (approximately −1.4 V). SSRT was performed at a strain rate of 10⁻ ⁵ s⁻ ¹ in accordance with ASTM G129-21. Tensile specimens extracted from the base material and welded joints were tested in air and under hydrogen-charging conditions. The methodology enabled controlled hydrogen introduction during deformation of tensile probes and allowed comparison of hydrogen-assisted cracking susceptibility between base metal and welded material. Tested brocken tensile probes were subjected to determination of dissolved hydrogen. Tensile probes were first tested in the air and after that in prepared solution.
    To analyse hydrogen embritlement of investigated steel hydrogen embritlement index was determined through determination of fracture elongation and reduction of Area (RA) of the brocken specimen. Light and SEM microscopy was used to analyse possible location of the present defects in material i.e. hot rolled steel. Types of non-metallic inclusions were determined too.

  • Rolling element bearing fault detection using accelerometer and laser displacement measurements

    pg(s) 65-68

    Rolling element bearing fault detection is of significant importance due to the widespread use of bearings across numerous industrial applications. In this study, vibration measurements using an accelerometer and a laser displacement sensor are carried out on a laboratory bearing test rig under different operating conditions, including a healthy state and bearings with localized inner- and outer-ring faults. Measurements are conducted at a constant rotational speed of 1700 rpm and the acquired signals are analysed to extract characteristic features associated with potential bearing faults. The results demonstrate that the applied methodology enables indicative bearing fault detection using both measurement approaches.

  • Fiberglass casing string cementation operations in wellbore

    pg(s) 59-62

    Casing string is critical component in wellbore construction, defining wellbore diameter and providing structural integrity throughout drilling and production operations. Traditionally, steel casings are generally used due to their mechanical strength; however, problems connected with corrosion, particularly in environments containing hydrogen sulfide or saline formation water, presents significant operational and financial challenges. This paper explores the use of fiber-reinforced plastic (FRP) casing as a corrosion-resistant alternative, focusing on glass fiber-reinforced epoxy composites, especially concerning cementing operation. FRP casing properties depend on the fiber–matrix composition, fiber type, and manufacturing quality, which affect tensile and compressive strength, thermal stability, and resistance to environmental degradation. Laboratory and field studies, including pilot projects in Argentina, Oman, Brunei, and Kuwait, evaluated casing handling, rig down speed, anchoring, and cement bonding. Special attention was given to cementation procedures, fluid formulations for mud cake removal, and ultrasonic methods for assessing casing-to-cement bonding, adapted for the acoustic characteristics of FRP materials. Results indicate that while steel casings exhibit superior cement bonding, FRP casings can achieve adequate structural performance when mechanical stresses during handling and installation are carefully controlled and proper chemical compatibility between fluids and cement is ensured. Field data show that FRP casings can be deployed with only minor reductions in installation speed for smaller diameters and that optimized handling and cementation practices are crucial for operational success. These data demonstrate that FRP casings offer a technically feasible and economically advantageous alternative for wells in highly corrosive environments. However, their successful implementation requires tailored operational procedures, including modified handling equipment, optimized fluid systems, and specialized evaluation methods. Further field studies are needed to develop comprehensive guidelines for widespread adoption.

  • Kinetic investigation of copper ions adsorption onto corn stalks

    pg(s) 56-58

    Corn stalk was used as a biosorbent for the adsorption of copper ions from synthetic solutions. To examine the mechanism of the adsorption process and identify the potential rate-determining step, the following kinetic models were used in this study: the pseudo-first order kinetic model, the pseudo-second order kinetic model, the Elovich kinetic model, and the interparticle diffusion model. Kinetic studies show that copper ions adsorption followed the pseudo-second order kinetic model. The maximum adsorption capacity was 5.5 mg g⁻¹. The results indicate that corn stalk can be successfully used as a biosorbent for the adsorption of copper ions from synthetic solutions.

  • Analytical-numerical approach for computation of welding residual stresses in large shell structures

    pg(s) 22-25

    In this paper, the inherent strain method is employed for the purpose of predicting welding residual stresses in large shell structures. Such structures include roof structures in the construction industry and deck sections in the shipbuilding industry. The study focuses on the numerical aspect of the inherent strain method, with the objective of investigating the most appropriate technique for transferring analytically calculated inherent strains into the elastic finite element model of the structure. The approach under consideration takes into account the thermally induced stresses, to the extent that they are considered to be significant for the structures and their behaviour in question, with the objective of determining the field of welding residual stresses over the entire structure (macro-scaled). The work proposes theoretical parameters for the alignment of finite element meshes within the weld seam domain. The discussion in the conclusion encompasses the general application capabilities, limitations, and challenges for further development

  • Finite Element Modeling of a Flat Reinforced Expanded Polytetrafluoroethylene Gasket

    pg(s) 18-21

    The porosity of flat ePTFE gaskets imposes requirements on the compression force during installation. Improving the tightness when using such gaskets is achieved by reinforcing them in a certain area. The combination of the complicated shape and the highly nonlinear properties of the material used necessitates the creation of an appropriate numerical model, through which to determine the compression force necessary to ensure the required tightness. In this work, a simulation using the finite element method has been created and used, which is based on the Marlow material model and a viscoelastic model of shear stress relaxation. Results have been obtained for the hydrostatic stress, the minimum principal strains and the fluid leakage path. The threshold values of the minimum principal strain at different magnitudes of the compression force have been determined.

  • Forecast-oriented optimization of production plans: closed-loop decision-making and model risk management

    pg(s) 14-17

    : This paper presents a forecast-oriented optimization framework for production and technological planning in modern metallurgical manufacturing systems. Forecasts of demand, raw material availability, and external constraints are widely used in the development of production plans; however, in traditional optimization models, forecast information is typically treated as a fixed input parameter, which leads to model risk and reduced robustness of decision-making. Within the proposed framework, forecasts are interpreted as dynamic and potentially inaccurate elements of the control system, and planning is performed in a closed-loop feedback structure integrating forecasting, model risk management, and optimization. The paper describes the architecture of an integrated forecast-oriented planning system and reports the results of computational experiments on the problem of forming a technological production plan for secondary aluminum alloys. The results demonstrate the impact of forecast accuracy on product cost and the computational complexity of the optimization process.