Innovations
Vol. 9 (2021), Issue 2, pg(s) 69-72

INNOVATIVE SOLUTIONS

Application of progressive technologies in the restoration of functional areas of products

  • 1 Technical University of Košice, Faculty of Mechanical Engineering, Slovakia
  • 2 Slovak Academy of Sciences, Institute of Materials Research, Košice, Slovakia

Abstract

The paper presents the results of research focused on the restoration of functional areas of products by the application of PTA technology. Hardfacing layers intended for the renovation of the surfaces of aluminum alloy injection molds were evaluated. The base material was medium alloy steel X38CrMoV5-1 (H11). Three types of powder additives were applied to form the functional layers: two types based on iron, designated HSS 23 and HSS 30, and one type based on nickel, designated DEW Nibasit 625 -P. The quality of the layers was evaluated using non-destructive and destructive tests. The surface integrity of the layers was assessed by visual and capillary tests. The microstructure of the materials and its hardness were evaluated. The tribological properties of the welds were determined by the pin-on-disc method.

Keywords

References

  1. R. Venkatesh, Vaddiseahagiri Rao, N. Arunkumar Wear analysis on silicon carbide coated HSS pin on SS disc substrate Procedia Mater. Sci., 10 (2015), pp. 644-650
  2. S. Sunil, Jayaram C. Sasi Experimental wear analysis of boron carbide (B4C) coated high speed steel substrate J. Res., 02 (08) (2016), pp. 1-5
  3. A. Shah, S. Izman, M.R. Abdul-Kadir, H. MasAyu Influence of substrate temperature on adhesion strength of TiN coating of biomedical Ti–13Zr-13Nb alloy Arabian J. Sci. Eng., 42 (2017), pp. 4737-4742
  4. N. Bagc ivan, K. Bobzin, T. Brögelmann, C. Kalscheuer Development of (Cr, Al)ON coatings using middle frequency magnetron sputtering and investigations on tribological behavior against polymers Surf. Coat. Technol., 260 (15) (2014), pp. 347-361
  5. A.P. Rubshtein, A.B. Vladimirov, Y.V. Korkh, Y.S. Ponosov, S.A. Plotnikov The composition, structure and surface properties of the titanium-carbon coatings prepared by PVD technique Surf. Coat. Technol., 309 (2017), pp. 680-686
  6. C.H.M. Maia, R.O. Cunha Lima Comparative study of surface modification techniques through average flank wear in high speed steel tools coated with thin TiN film Surf. Coat. Technol., 366 (2019), pp. 124-130
  7. A. Devaraju A critical review on different types of wear of materials Int. J. Mech. Eng. Technol., 6 (11) (2015), pp. 77-83
  8. A. Devaraju A review on important factors affecting dry sliding friction J. Surf. Sci. Technol., 32 (3–4) (2016), pp. 73-78
  9. T. Pridhar, K. Ravikumar, B. Sureshbabu, R. Srinivasan, B. Sathishkumar Multi objective optimization of wear characteristics on Al 7075/Al2O3/B4C composites - Desirability approach J. Ceram. Process. Res., 21 (2) (2020), pp. 131-142
  10. R. Srinivasan, T. Pridhar, R. Kirubakaran, A. Ramesh Prediction of wear strength of squeeze cast aluminium hybrid metal matrix composites using response surface methodology Mater. Today Proc., 27 (P2) (2020), pp. 1806-1811
  11. Jorge Salguero, Juan Manuel Vazquez-Martinez, Irene Del Sol, Moises Batista Application of pin-on-disc techniques for the study of tribological interferences in the dry machining of A92024–T3 (Al–Cu) alloys Materials (Basel), 11 (7) (2018), p. 1236
  12. N.S. Mahesha, R. Hanumantharaya, B. Mahesh, P. Ramakrishna Davanageri, K.M. Shivakumar Devananda Tribological wear Behavior of AISI 630 (17–4 PH) Stainless steel hardened by precipitation hardening Am. J. Mater. Sci., 6 (4A) (2016), pp. 6-14
  13. R. Kaczyński, B. Hościło Examination of the coating of a cutting tool based on measurements microhardness and scratch tests J. Frict. Wear, 38 (2) (2017), pp. 108-114
  14. A.S. Chaus Microstructural and properties evaluation of M2 high speed steel after inoculating addition of powder W and WC Adv. Phys. Metall. Steels, 30 (9) (2014)
  15. D. Kottfer, M. Ferdinandy, L. Kaczmarek, I. Mankova, J. Beno Investigation of Ti and Cr based PVD coating deposited onto HSS Co5 twist drills Appl. Surf. Sci., 282 (2013), pp. 770-776
  16. B. Podgornik, B. Zajec, N. Bay, J. Vižintin Wear, 270 (2011), pp. 850-856
  17. C. Nouveau, B. Tlili, H. Aknouche, Y. Benlatreche, B. Patel Thin Solid Films, 520 (2012), pp. 2932-2937
  18. A. Yazdani, M. Soltanieh, H. Aghajani, S. Rastegari A new method for deposition of nano sized titanium nitride on steels J. Vac., 86 (2011), pp. 131-139
  19. B. Denkena, J. Köhler, B. Breidenstein, A.M. Abrão, C.E.H. Ventura Influence of the cutting edge preparation method on characteristics and performance of PVD coated carbide inserts in hard turning J. Surf. Coat. Technol., 254 (2014), pp. 447-454,
  20. K.J.B. Ribeiro, R.R.M. de Sousa, F.O. de Aráujo, R.A. de Brito, J.C.P. Barbosa, C. Alves Jr. Industrial application of AISI 4340 steels treated in cathodic cage plasma nitriding technique Mat Sci Eng A, 479 (2008), pp. 142-147

Article full text

Download PDF